===== MM =====
=== TeleType Communications === 
MM sets the Brewer program to its teletype (terminal) mode, whereby the operator may communicate directly with the Brewer via the computer keyboard and a set of low level commands. \\
Exit from teletype mode by typing EXIT. 
See Appendix H for more explanation on the TeleType feature.\\

===== List of commands =====
^Command^Variables^Usage^Description^
|A| | |Repeats the command. Usually use in conjunction with another command move. (I.E. R,0,7,5:O:A) Press home to delete twice to go exit.|
|B,x| \\
  x refers to the following
  0. Turns off all lamp
  1. Turns on the mercury lamp
  2. Turns on the standard lamp
|B,2|This command controls the lamps|
|M,m,s|\\
  m refers to a motor number
  1. Zenith prism
  2. Azimuth Tracker
  3. Iris
  4. Filterwheel 1
  5. Filterwheel 2
  6. Filterwheel 3
  9. Micrometer 2 (Bottom)
  10. Micrometer 1 (Top)
  11. Slitmask 1
  12. Slitmask 2
  13. Zenith tracker
   
  s refer to the number of steps to move
|M,10,500|Moves motor m to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
|O| |O|This command outputs the number of counts returned in a measurement.
|R,p1,p2,t|\\
  p# refers to the slit positions
  t refers to number of times to repeat
|R,0,5,7|This command is used to measure the light intensity according to the variables setup. Often this command is combined with the O command to output the results. R,0,5,7:O|
|SL| |SL|  \\
    - Turn the SL bulb on
    - Points the zenith down
    - Open the iris
    - Set FW1 to position 1
    - Set FW2 to position 0
|
|SL+| |SL|  \\
    - Turn the SL bulb on
    - Points the zenith down
    - Open the iris
    - Set FW1 to position 1
    - Set FW2 to position 0
    - R,0,7,1;o
|
|HG+| |HG+|  \\
    - Turn the SL bulb on
    - Points the zenith down
    - Open the iris
    - Set FW1 to position 1
    - Set FW2 to position 0
    - R,0,7,1;o
|
|FW<key>filter wheel number</key>,<key>position</key>|<key>filter wheel number</key> Filter wheel 1 or 2 \\ <key>position</key> - What position to move to|FW1,2|Move the selected filter wheel to the selected position|
|T<key>Start Location</key>2<key>End Location</key>| \\
  Start Location and End Location 
  can be any of the following
  1. MAX - Maximum micrometer position
  2. OP - operating micrometer position
  3. MIN - minimum micrometer position
|TOP2MAX|This command will move the micrometer 1 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.|
|B<key>Start Location</key>2<key>End Location</key>| \\
  Start Location and End Location 
  can be any of the following
  1. MAX - Maximum micrometer position
  2. OP - operating micrometer position
  3. MIN - minimum micrometer position
|BOP2MAX|This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.|
|exit|  |exit|exit's mm and return to menu ('quit' will do the same thing)|
\\  
==== For multiboard electronics only ====
^Command^Variables^Usage^Description^
|E,m| \\
  m refers to a motor number
  1. Zenith prism
  2. Azimuth Tracker
  3. Iris
  4. Filterwheel 1
  5. Filterwheel 2
  6. Filterwheel 3 or Micrometer 2 (bottom)
  10. Micrometer 1 (Top)
  11. Slitmask 1
  12. Slitmask 2
  13. Zenith tracker
|E,9|This command zeros the motor and return the number it takes to get to the LED. NOTE: This will not return the motor and will leave it at the LED|
|x,s1,s2|s1 and s2 refers to the number of steps to move for micrometer 1 and 2 respectively.|x,100,200|Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|


==== For new electronics only ====
^Command^Variables^Usage^Description^
|?<command> OR !<command>|See [[operation_information|Operation Information]]|:::|A variety of operational commands/status output for the brewer.  for more.|
|I,m| \\
  m refers to a motor number
  1. Zenith prism
  2. Azimuth Tracker
  3. Iris
  4. Filterwheel 1
  5. Filterwheel 2
  6. Filterwheel 3
  9. Micrometer 2 (Bottom)
  10. Micrometer 1 (Top)
  11. Slitmask 1
  12. Slitmask 2
  13. Zenith tracker
|
|I,9|This commands re-initializes the specified motor|
|N,s|s refers to the number of steps|N,500|(Used for [[singleboard|singleboard electronics]] only.) Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
|SAVE|   |SAVE|Stores the current set of RAM configuration parameters|
|?MZ10|   |?MZ10|Runs the command <key>?MOTOR.ZERO.POS[10]</key>|
|?MZ9|   |?MZ9|Runs the command <key>?MOTOR.ZERO.POS[9]</key>|
|?MP10|   |?MP10|Runs the command <key>?MOTOR.POS[10]</key>|
|?MP9|   |?MP9|Runs the command <key>?MOTOR.POS[9]</key>|
|?MD10|   |?MD10|Runs the command <key>?MOTOR.DISCREPANCY[10]</key>|
|?MD9|   |?MD9|Runs the command <key>?MOTOR.DISCREPANCY[10]</key>|