====== Operation Information ======


Syntax

? for read
! for write
^name^Format of value^writeable^Description^
|ANALOG.NOW [<analogPt>]|10-bit integer|no|A/D output value in A/D units|
|BREAK.ABORT.TIME |float seconds|Yes, reset to 0.25 on tepid resets|The elapsed time in seconds for a continuous TTY line-break to abort command processing.|
|BREAK.RESET.TIME|float seconds|Yes, reset to 5.0 on tepid resets|The elapsed time in seconds for a continuous TTY line-break to force a warm restart of the Brewer.|
|BYTE.X [<address>]|ANSI C integer format (Hex on output)|yes|value of the relevant byte in external RAM|
|BYTE.F [<address>]|ANSI C integer format (Hex on output)|no|reads value from Flash memory|
|BYTE.C [<address>]|ANSI C integer format (Hex on output)|no|value of the relevant byte in CODE space|
|BYTE.D [<address>]|ANSI C integer format (Hex on output)|yes|value of the relevant byte in DATA space
|DIGITAL.INPUT [<digitalPt>]|OFF or ON|no|reads whether input is ON or OFF; logic levels are transparent to the user.|
|DIGITAL.OUTPUT [<digitalPt >]|OFF or ON|yes|digital output point ON or OFF with logic levels transparent to the user.|
|ECHO.SUPPRESSION|ON/OFF|:::|Suppresses TTY mode echoing when ON, allows echoing when OFF.|
|HG.SWITCH|OFF or ON|yes|mercury lamp set OFF or ON|
|STD.SWITCH|OFF or ON|yes standard lamp set OFF or ON|
|LAMP.POWER [<lamp>]|watts|no|lamp power consumption|
|LAMP.STATE [<lamp>]|lamp state type|yes|state of lamp (OFF or ON)|
|MOISTURE|Grams/cu. m|no|Moisture content of air inside the Brewer|
|MOISTURE.HIGH|Grams/cu m|yes|Moisture content high (watermark)|
|MOTOR.ALLSTILL|TRUE or FALSE|no|True only if all the motors have stopped moving|
|MOTOR.POS [<motorId>]|steps|no current motor position|
|MOTOR.LOST [<motorId>]|Boolean|no|current motor position unknown exactly|
|MOTOR.LIMIT.LOW [<motorId>]|Boolean|no|low travel limit sensor activated|
|MOTOR.LIMIT.HIGH [<motorId>]|Boolean|no|high travel limit sensor activated
|MOTOR.REF.LOW [<motorId>]|Boolean|no|lower reference sensor (#1) activated (Low = Mirror side, or high number when doing an FR)|
|MOTOR.REF.HIGH [<motorId>]|Boolean|no|upper reference sensor (#2) activated (High = bulkhead side , or 0 when doing an FR)|
|MOTOR.DISCREPANCY [<motorId>]|paces|no|position of the reference position on the most recent motor initialization. This is a measure of accumulated motor position error between the most recent and the immediately prior initialization.|
|MOTOR.ZERO.POS [<motorId>]|signed integer paces|no|the same as MOTOR.ORIGIN on a reset, but is updated by negative M commands.|
|PMT.SELECT|integer (1 to 3)|yes|selects the PMT in use; 3 means both RH % no Relative Humidity inside the Brewer|
|STEPS|integer steps|no|the number of steps in a complete revolution of the azimuth tracker|
|SUPPLY.VOLTAGE.HIGH [<powerSupply>]|volts|yes|supply voltage high (watermark)|
|SUPPLY.VOLTAGE.LOW [<powerSupply>]|volts|yes|supply voltage low (watermark)|
|SUPPLY.VALUE [<powerSupply>]|volts|no|supply voltage|
|SUPPLY.SETTING.HV|volts|no|HV supply setting recorded at last adjustment.|
|TEMP.HIGH [<thermalPoint>]|degrees|yes|lamp power consumption high (watermark)|
|TEMP.LOW [<thermalPoint>]|degrees|yes|lamp power consumption low (watermark)
|TEMP [<thermalPoint>]|degrees|no|lamp power consumption|
|TIME|<year> <day> <hour> <min> <sec>|yes|<YYYY> <DDD> <HH> <MM> <SS> (In Julian date)|
|TRACKER.SWITCH.SETTING [<trackerSwitch >]|ON/OFF|no|reports the debounced tracker switch status that is indexed
|TRACKER.SWITCHES|integer bit map|no|bit is on if the switch (see <trackerSwitch) is currently pressed. These are debounced values.
|TTY.FILL.CHARACTER|integer ASCII (0-255)|yes|TTY mode echo character ASCII code|
|TTY.FILL.COUNT|integer count (0-255)|yes|TTY echo character padding count
|VERSION.FW[<info>]|integer|no|Version information and design date for the firmware. <info> is one of:YEAR, MONTH, DAY, VERS, REL|