Differences

This shows you the differences between two versions of the page.

--- faq [2023/08/27 19:13] – [Lamps] mbrohart
+++ faq [2023/11/30 14:32] (current) – reno
@@ Line 5: / Line 5: @@
 **A:** Ensure brightest part of the band of light is sitting in the middle of the Iris. There are two ways to accomplish this.++++ More...|
   - Manually adjusting by loosening the zenith shaft and moving the shaft until the band of light lines up as shown in the picture. \\ {{ :misc:misc:sl_band.png?600 |}}
-  - Doing a ZI, this will do a shorten DI where it only checks for the zenith position.\\ {{:misc:zi.jpg?600|}} \\ As shown on the graph above, the zenith is -1 step off. Therefore the Offsets needs to be changed as follows. \\  * For MB electronics, the offset is clockwise from the reference, so the Zenith Offset: +1 I.E. Original: 100, New: 101 however in SB electronics the Zenith Motor origin moves counter clockwise so the Motor.Origin[1]: (gets smaller) Zenith Origin: -1 I.E. Original: 5, New: 4 \\ * UV Offset +1 I.E. Original: 2109, New 2110 \\ * Sighting HC: +1 I.E. Original: -5, New -4 \\ **Note: After changing the sighting, its advisable to have the operator to verify the new sighting.**
+  - Doing a ZI, this will do a shorten DI where it only checks for the zenith position.\\ {{:misc:zi.jpg?600|}} \\ As shown on the graph above, the zenith is -1 step off. Therefore the Offsets needs to be changed as follows. \\  * For MB electronics, the offset is clockwise from the reference, so the Zenith Offset: +1 I.E. Original: 100, New: 101\\ * For SB electronics the Zenith Motor origin moves counter clockwise so the Motor.Origin[1]: (gets smaller) Zenith Origin: -1 I.E. Original: 5, New: 4 \\ * UV Offset +1 I.E. Original: 2109, New 2110 \\ * Sighting HC: +1 I.E. Original: -5, New -4 \\ **Note: After changing the sighting, its advisable to have the operator to verify the new sighting.**
 ++++
@@ Line 50: / Line 50: @@
 ===== Software =====
-**Q:** How do I remote into _______ site?\\
-**A:** You can connect to most site with [[https://007gc-my.sharepoint.com/:f:/g/personal/reno_sit_ec_gc_ca/EiKYKdxFTDZBsSfJY22y180Bxpj-AjRXzdU8dIpFgm9Brg?e=snqErV|sshvnc]]++ |Note: You must login to your @ec.gc.ca email and use a compatible browser  to access the files. |++\\
-//Note:// SPO requires a few extra steps, see [[spo#vnc|SPO]]
 **Q:** How do I launch a GUI via remote ssh?\\
@@ Line 61: / Line 57: @@
 **A:** Type: :%s/^M/ /g\\ (note to type in ^M <key>ctrl</key>+<key>v</key> <key>ctrl</key>+<key>m</key>)\\
-===== Calculators  =====
-**Q: ** How do you convert elevation to pressure?\\
-**A:** <hidden>{{url>https://docs.google.com/spreadsheets/d/1hmbdtdmBm1qkZ7CzCReBejJxKpv3yHvXS9Qi36LDgRo/edit?rm=minimal}}</hidden>
-<ifauth @admin>
-===== Brewer Processing =====
-**Q:** Where do you check what constants file is being used for the data processing?\\
-**A:** <code>\\wontlabj105896\C\Ic
-\\wontlabj105896\C\Uvr</code>
-</ifauth>
 ===== DosBox Key Mapper =====
 https://www.dosbox.com/wiki/Mapper\\