Differences

This shows you the differences between two versions of the page.

--- mm [2020/11/19 18:47] – added A command sitr
+++ mm [2025/08/13 05:33] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
-====== MM ======
+===== MM =====
+=== TeleType Communications ===
-MM is a command that puts you into the teletype (terminal) of the Brewer Spectrometer.
+MM sets the Brewer program to its teletype (terminal) mode, whereby the operator may communicate directly with the Brewer via the computer keyboard and a set of low level commands. \\
+Exit from teletype mode by typing EXIT.
+See Appendix H for more explanation on the TeleType feature.\\
 ===== List of commands =====
@@ Line 25: / Line 27: @@
 . Slitmask 2
 . Zenith tracker
+  s refer to the number of steps to move
 |M,10,500|Moves motor m to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
 |O| |O|This command outputs the number of counts returned in a measurement.
@@ Line 31: / Line 35: @@
   t refers to number of times to repeat
 |R,0,5,7|This command is used to measure the light intensity according to the variables setup. Often this command is combined with the O command to output the results. R,0,5,7:O|
+|SL| |SL|  \\
+    - Turn the SL bulb on
+    - Points the zenith down
+    - Open the iris
+    - Set FW1 to position 1
+    - Set FW2 to position 0
+|
+|SL+| |SL|  \\
+    - Turn the SL bulb on
+    - Points the zenith down
+    - Open the iris
+    - Set FW1 to position 1
+    - Set FW2 to position 0
+    - R,0,7,1;o
+|
+|HG+| |HG+|  \\
+    - Turn the SL bulb on
+    - Points the zenith down
+    - Open the iris
+    - Set FW1 to position 1
+    - Set FW2 to position 0
+    - R,0,7,1;o
+|
+|FW<key>filter wheel number</key>,<key>position</key>|<key>filter wheel number</key> Filter wheel 1 or 2 \\ <key>position</key> - What position to move to|FW1,2|Move the selected filter wheel to the selected position|
+|T<key>Start Location</key>2<key>End Location</key>| \\
+  Start Location and End Location
+  can be any of the following
+. MAX - Maximum micrometer position
+. OP - operating micrometer position
+. MIN - minimum micrometer position
+|TOP2MAX|This command will move the micrometer 1 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.|
+|B<key>Start Location</key>2<key>End Location</key>| \\
+  Start Location and End Location
+  can be any of the following
+. MAX - Maximum micrometer position
+. OP - operating micrometer position
+. MIN - minimum micrometer position
+|BOP2MAX|This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.|
+|exit|  |exit|exit's mm and return to menu ('quit' will do the same thing)|
+\\
+==== For multiboard electronics only ====
+^Command^Variables^Usage^Description^
+|E,m| \\
+  m refers to a motor number
+. Zenith prism
+. Azimuth Tracker
+. Iris
+. Filterwheel 1
+. Filterwheel 2
+. Filterwheel 3 or Micrometer 2 (bottom)
+. Micrometer 1 (Top)
+. Slitmask 1
+. Slitmask 2
+. Zenith tracker
+|E,9|This command zeros the motor and return the number it takes to get to the LED. NOTE: This will not return the motor and will leave it at the LED|
+|x,s1,s2|s1 and s2 refers to the number of steps to move for micrometer 1 and 2 respectively.|x,100,200|Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
 ==== For new electronics only ====
 ^Command^Variables^Usage^Description^
+|?<command> OR !<command>|See [[operation_information|Operation Information]]|:::|A variety of operational commands/status output for the brewer.  for more.|
 |I,m| \\
   m refers to a motor number
@@ Line 46: / Line 109: @@
 . Slitmask 2
 . Zenith tracker
+|
 |I,9|This commands re-initializes the specified motor|
-|SAVE||SAVE|Stores the current set of RAM configuration parameters|
+|N,s|s refers to the number of steps|N,500|(Used for [[singleboard|singleboard electronics]] only.) Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
+|SAVE|   |SAVE|Stores the current set of RAM configuration parameters|
+|?MZ10|   |?MZ10|Runs the command <key>?MOTOR.ZERO.POS[10]</key>|
+|?MZ9|   |?MZ9|Runs the command <key>?MOTOR.ZERO.POS[9]</key>|
+|?MP10|   |?MP10|Runs the command <key>?MOTOR.POS[10]</key>|
+|?MP9|   |?MP9|Runs the command <key>?MOTOR.POS[9]</key>|
+|?MD10|   |?MD10|Runs the command <key>?MOTOR.DISCREPANCY[10]</key>|
+|?MD9|   |?MD9|Runs the command <key>?MOTOR.DISCREPANCY[10]</key>|