Differences

This shows you the differences between two versions of the page.

--- singleboard [2025/01/28 15:55] – [Commands] volodya
+++ singleboard [2025/12/05 05:33] (current) – external edit 127.0.0.1
@@ Line 4: / Line 4: @@
 ¹Note, both multiboard and single board electronics both have an PPS, however the multiboard uses a 24V/15V/5V power supply while the single board electronics uses 24V/12V/5V power supply. The latest brewer's produced by Kip and Zonen (around Brewer # 250) uses the TDK-Lambda NV175 series power supply. The single Electronics board uses NV1-4G5TT, where the multiboard uses the NV14G5FF.
+===== Version 1 boards =====
+<hidden Single Board Top>{{ :boards:singleboard_v1_top.jpg?600 |Single Board Top V1}}</hidden>
+<hidden Single Board Bottom>{{ :boards:singleboard_v1_bottom.jpg?600 |Single Board Bottom V1}}</hidden>
+<hidden Voltage Test Point>
+^Connect J23^   Pin   ^^^^^^^^^^
+^:::^1^2^3^4^5^6^7^8^9^10^
+|   |5v|5v|-5v|12v|12v|-12v|24|2.5v|4.5v|GND|
+</hidden>
 {{ :docs:brewer_mkiii_operators_manual_revd.pdf |Operator Manual}}\\
 {{ :docs:mkiii_service_manual_revd_sb.pdf |Service Manual}}
-===== Mainboard Flat Cable Connections =====
+===== Version 2 Boards =====
-^Cable^Name^Useage^
+<hidden Single Board Top>{{ :boards:singleboard_v2_1_top.jpg?600 |Single Board Top V2 Section 1}}{{ :boards:singleboard_v2_2_top.jpg?600 |Single Board Top V2 Section 2}}</hidden>
-|J2 Top|BA-W77/A|Lamp Board|
+<hidden Single Board Bottom>{{ :boards:singleboard_v2_1_bottom.jpg?600 |Single Board Bottom V2 Section 1}}{{ :boards:singleboard_v2_2_bottom.jpg?600 |Single Board BottomV2 Section 2}}}</hidden>
-|J2 Bottom|BA-W77/B|J1 on hv module|
+{{ :docs:kz_splitboard_pcb_layout_a.pdf |}}\\
-|J13 Top|BA-W76/B|Iris|
+{{ :docs:kz_splitboard_pcb_layout_b.pdf |}}
-|J13 Bottom|BA-W76/A|Zenith|
-|J14 Top|BA-W76/B|Filter wheel #1|
-|J14 Bottom|BA-W76/B|Filter wheel #2|
-|J15 Top|BA-W76/A|Micrometer #2 (MKIII only)|
-|J15 Bottom|BA-W76/A|Micrometer #1|
-|J16 Bottom|BA-W76/C|Filter wheel#3 (MK IV only}|
-|J17 Top|BA-W76/B|Slitmask (shutter)|
-|J17 Bottom|BA-W76/A|Azimuth|
-|J12 Top|BA-W76/A|Control switch’s|
-|J7 Top| |Communication|
-|J7 Bottom| |Humidity sensor|
-===== SL/HG adjustments=====
+===== Mainboard Flat Cable Connections =====
+^Cable^Name^Useage^Default Address^Jumper settings^
+|J2 Top|BA-W77/A|Lamp Board|  |   |
+|J2 Bottom|BA-W77/B|J1 on hv module|  |   |
+|J13 Top|BA-W76/B|Iris|Motor 3|**[E35 E37]** (E38 E38)|
+|J13 Bottom|BA-W76/A|Zenith|Motor 1|**[E39 E40]** (E41 E42)|
+|J14 Top|BA-W76/B|Filter wheel #1|Motor 4|**[E71 E72]** (E73 E74)|
+|J14 Bottom|BA-W76/B|Filter wheel #2|Motor 5|**[E75 E76]** (E77 E78)|
+|J15 Top|BA-W76/A|Micrometer #2 (MKIII only)|Motor 9|[E107 E108] **(E109 E110)**|
+|J15 Bottom|BA-W76/A|Micrometer #1|Motor 10|[E111 E112] **(E113 E114)**|
+|J16 Top|  |Spare|Motor 7|[E143 E144] (E145 E141)|
+|J16 Bottom|BA-W76/C|Filter wheel#3 (MK IV only}|Motor 6|**[E147 E148]** (E149 E150)|
+|J17 Top|BA-W76/B|Slitmask (shutter)|Motor 11|**[E179 E182]** (E181 E182)|
+|J17 Bottom|BA-W76/A|Azimuth|Motor 2|   |
+|J12 Top|BA-W76/A|Control switch’s|  |   |
+|J12 Bottom|  |  |  |   |
+|J20 Top|   |Spare|Motor 12|[E7 E8] (E9 E10)
+|J20 Bottom|  |Spare - New AZ motor|Motor 8|
+|J7 Top| |Communication|  |
+|J7 Bottom| |Humidity sensor|  |
+Note 1: Top Refers to the connector on the stop of the ribbon connector stack on a V1 board when looking at it on a birds eye view. For V2 boards, it is the connector closer to the bottom of the board.\\
+Note 2: From the table above, J2 is the connector on the top right of the board, and going left. J7 is on the bottom right of the board.\\
+Note 3: [] indicates 12V pair and () indicates 24V pair and **bold** indicates jumper default
+===== Lamp/Temp Board=====
 {{:misc:20201019_074344_resized.jpg?300|}}
 |SL Voltage|HG Voltage|SL Current|
+===== Brewer Base Plate =====
+<hidden Single Board Brewer Base Plate Drawing>{{:brewer_main:single_board_base_detail-1.jpg?400|}}
+{{:brewer_main:single_board_base_holes-1.jpg?400|}}
+{{:brewer_main:single_board_bm-c215_rev_1_spectrometer_weatherproof_base-1.jpg?400|}}</hidden>
+\\
+==== Troubleshooting ====
+=== AP Lamps Results ===
+Possible issues with via AP results
+^:::^Working Order^^Disconnected DB connector @ Lamp^^No power to Lamp Board^^Missing 24V @ Lamp Board^^Bad Connection on Power connector¹^^
+^Name^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^
+|Std Lamp current(A)|0.00|1.51|0.01|0.00|0.02|0.01|0.01|0.00|2.48|2.48|
+|Std Lamp Voltage(v)|0.03|10.44|6.84|12.83|5.29|3.16|0.04|0.03|14.09|14.06|
+|Mer Lamp current(A)|0.00|0.46|0.01|0.23|0.00|0.00|0.00|0.00|0.00|0.00|
+|Mer Lamp Voltage(v)|0.54|12.86|0.56|12.88|5.48|3.25|0.03|0.01|14.81|14.11|
+¹More testing required.
+=== Status LED ===
+^LED Mode Indication^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^
+^Cosmac Mode normal operation|**on**|off|off|off|**on**|**on**|**on**|off|
+^Cosmac Mode with config missing|**on**|off|off|off|**on**|off|**on**|off|
+^Loadmode Waiting for firmware|**on**|off|**on**|off|**on**|off|**on**|off|
+^Loadmode with bad flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
+^Loadmode with Good flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
+^Opmode with config|**on**|**on**|off|off|**on**|**on**|off|off|
+^Opmode without config|**on**|**on**|off|off|**on**|off|**on**|off|
+^Checking flash memory|**on**|off|**on**|off|off|off|off|off|
+^Changing modes|**on**|**on**|**on**|**on**|**on**|**on**|**on**|**on**|
 ===== Commands =====
-Frequently used commands in MM/TT
+Frequency used commands in MM
 ^Command^description^
 |I,<key>x</key>|Resets motor <key>x</key>|
@@ Line 36: / Line 85: @@
 |?motor.ref.low[<key>x</key>]|checks the reference flag of motor <key>x</key> on the low side|
 |?motor.address.[<key>MOTOR</key>]|checks the motor address used for <key>MOTOR</key>|
+==== Changing Motor Address ====
+The motor address can be changed in event of a bad motor driver or circuitry. This will require the ribbon cable to be physically moved to another connector as laid out [[singleboard#mainboard_flat_cable_connections|here]]. Afterwards, enter [[mm|MM]] or opmode in brewcmd.
+<konsole mm>
+?motor.address[motorname]
+#This will output the current motor address number, verify this is the one you want to change\\
+!motor.address[motorname] 7
+#replace 7 with the actual address you'd like to change to\\
+i,10
+#replace the 10 with the original address, this will reinitialize the motor\\
+save
+#once you verify everything is working as expected, you can save which will use up on of the save slots.
+#otherwise when the brewer restarts, it'll be using the original motor address.
+</konsole>
+Note: anything starting with # are meant to be comments and not actual commands
-===== K&Z New Electronics=====
+==== Motor names ====
-{{ :docs:kz_splitboard_pcb_layout_a.pdf |}}\\
+  * AZIMUTH
-{{ :docs:kz_splitboard_pcb_layout_b.pdf |}}
+  * IRIS
+  * FILTER.WHEEL.1
+  * FILTER.WHEEL.2
+  * FILTER.WHEEL.3
+  * MICROMETER.2
+  * MICROMETER.1
+  * SLITMASK.1
+  * SLITMASK.2
+  * TRACKER.ZENITH
+  * ZENITH