mm
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| mm [2021/11/25 01:34] – mbrohart | mm [2025/08/13 05:33] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 27: | Line 27: | ||
| 12. Slitmask 2 | 12. Slitmask 2 | ||
| 13. Zenith tracker | 13. Zenith tracker | ||
| + | |||
| + | s refer to the number of steps to move | ||
| |M, | |M, | ||
| |O| |O|This command outputs the number of counts returned in a measurement. | |O| |O|This command outputs the number of counts returned in a measurement. | ||
| Line 33: | Line 35: | ||
| t refers to number of times to repeat | t refers to number of times to repeat | ||
| |R, | |R, | ||
| + | |SL| |SL| \\ | ||
| + | - Turn the SL bulb on | ||
| + | - Points the zenith down | ||
| + | - Open the iris | ||
| + | - Set FW1 to position 1 | ||
| + | - Set FW2 to position 0 | ||
| + | | | ||
| + | |SL+| |SL| \\ | ||
| + | - Turn the SL bulb on | ||
| + | - Points the zenith down | ||
| + | - Open the iris | ||
| + | - Set FW1 to position 1 | ||
| + | - Set FW2 to position 0 | ||
| + | - R,0,7,1;o | ||
| + | | | ||
| + | |HG+| |HG+| \\ | ||
| + | - Turn the SL bulb on | ||
| + | - Points the zenith down | ||
| + | - Open the iris | ||
| + | - Set FW1 to position 1 | ||
| + | - Set FW2 to position 0 | ||
| + | - R,0,7,1;o | ||
| + | | | ||
| + | |FW< | ||
| + | |T< | ||
| + | Start Location and End Location | ||
| + | can be any of the following | ||
| + | 1. MAX - Maximum micrometer position | ||
| + | 2. OP - operating micrometer position | ||
| + | 3. MIN - minimum micrometer position | ||
| + | |TOP2MAX|This command will move the micrometer 1 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.| | ||
| + | |B< | ||
| + | Start Location and End Location | ||
| + | can be any of the following | ||
| + | 1. MAX - Maximum micrometer position | ||
| + | 2. OP - operating micrometer position | ||
| + | 3. MIN - minimum micrometer position | ||
| + | |BOP2MAX|This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.| | ||
| + | |exit| | ||
| + | \\ | ||
| + | ==== For multiboard electronics only ==== | ||
| + | ^Command^Variables^Usage^Description^ | ||
| + | |E,m| \\ | ||
| + | m refers to a motor number | ||
| + | 1. Zenith prism | ||
| + | 2. Azimuth Tracker | ||
| + | 3. Iris | ||
| + | 4. Filterwheel 1 | ||
| + | 5. Filterwheel 2 | ||
| + | 6. Filterwheel 3 or Micrometer 2 (bottom) | ||
| + | 10. Micrometer 1 (Top) | ||
| + | 11. Slitmask 1 | ||
| + | 12. Slitmask 2 | ||
| + | 13. Zenith tracker | ||
| + | |E,9|This command zeros the motor and return the number it takes to get to the LED. NOTE: This will not return the motor and will leave it at the LED| | ||
| + | |x,s1,s2|s1 and s2 refers to the number of steps to move for micrometer 1 and 2 respectively.|x, | ||
| + | |||
| + | |||
| ==== For new electronics only ==== | ==== For new electronics only ==== | ||
| ^Command^Variables^Usage^Description^ | ^Command^Variables^Usage^Description^ | ||
| Line 49: | Line 109: | ||
| 12. Slitmask 2 | 12. Slitmask 2 | ||
| 13. Zenith tracker | 13. Zenith tracker | ||
| + | | | ||
| |I,9|This commands re-initializes the specified motor| | |I,9|This commands re-initializes the specified motor| | ||
| - | |SAVE||SAVE|Stores the current set of RAM configuration parameters| | + | |N,s|s refers to the number of steps|N, |
| + | |SAVE| | ||
| + | |? | ||
| + | |? | ||
| + | |? | ||
| + | |? | ||
| + | |? | ||
| + | |? | ||
mm.1637804043.txt.gz · Last modified: 2021/11/25 01:34 by mbrohart